BENCO-EQUIPMENT.COM | Automotive Special Tools

3050C
Noid Lite Test Kit

Noid Lites are a proven test device to quickly determine if the electrical signal is present at the fuel injector.

Just plug in and turn over the engine; flashing noid indicates good signal.

Expanded set of eight Noid Lites cover: GM PFI, Ford TBI, Geo TBI, Bosch PFI, GM TBI, GM SCPI, and now new applications of Bosch 2 and Multec 2.

Kit comes in molded plastic case and includes a harness extension that allows for convenient remote viewing from the driver’s seat.

3054C
Noid Lite/IAC Test Kit

Simplest method for eliminating the EFI system or idle air control as possible faults on no-start vehicles.

Disconnect the fuel injectors, plug in a Noid Lite, and crank the engine. A flashing light indicates normal pulsing voltage.

Expanded set of eight specific Noid Lites covers: GM PFI, Ford TBI, Geo TBI, Bosch PFI, GM TBI, GM SCPI, and now new applications of Bosch 2 and Multec 2, plus two GM IAC testers (flat and square four connector applications) with red and green LEDs.

Includes a molded plastic case and harness extension that allows for convenient remote viewing from the driver’s seat.

4490
Magnetic Parts Tray

Rectangular, stainless steel tray is 9-1/2" x 5-1/2" and 1-1/4" deep. Holds tools and small metal parts so they don’t get lost or misplaced during repair work.

Two heavy-duty magnets on bottom of tray have non-marring contact pads; will securely hold tray to metal objects such as a tool box, air cleaner cover, frame rail, fender, etc.

4491
Mechanic’s Stethoscope

Quick and accurate way to locate vehicle noise.

Spring diaphragm on end of hose amplifies noise.

Includes two hose ends: long rod helps pinpoint noises in hard-to-access areas; short adapter helps locate noise in a broader area of the vehicle.

4492
4-Piece E-Clip Tool Set

Dual operation tool: one end of tool releases e-clip; other end of tool installs e-clip.

Tools fit four sizes of e-clips: 6 mm, 7 mm, 8 mm, and 9 mm.

Each tool easily locks into handle provided.

4493
Angle-tip Relay Pliers

Designed to remove and install relays, which are usually located in confined, hard-to-reach areas.

Specially coated tips offer a solid grip on the relay.

4497
Ratcheting Terminal Crimper

Heavy-gauge steel crimping tool designed for insulated wire terminals.

Ratcheting action crimps terminal to correct tightness on the wire, making crimping fast and easy.

Insulated handles with compound mechanical leverage for power.

For wire sizes: AWG 22-18 (0.6mm—1.0mm) red terminal; AWG 16-14 (1.3mm –1.6mm) blue terminal; AWG 12-10 (2.0mm—2.6mm) yellow terminal.

4498
7-in-1 Wire Stripper & Crimper

Strips insulation off electrical wires ranging from 10 AWG—22 AWG (0.6mm—2.6mm) in diameter. Pliers on tip of jaw for looping or grabbing wire in tight places.

Heat-treated steel jaws cut solid or multi-strand wire.

Screw cutter shears screws clean, with no thread clean-up required. Works on machine screw sizes 4-40, 5-40, 6-32, 8-32, 10-24, and 10-32.

Crimps insulated and non-insulated wire terminals, 7mm—8mm spark plug wire connectors.

4502
Hose Clamp Plier Set

Includes a cross-slotted jaw pliers and a wide, flat-band hose clamp pliers. Services most ring-type or flat-band hose clamps.

The clamps are held open with a ratchet locking mechanism. Jaws swivel to access hose clamps in any position.

4503
Double Flaring Tool Kit

Designed for double or single flare in copper, aluminum, soft steel brake line, and brass tubing (to 45 degrees).

Includes five adapters 3/16" through 1/2" (4.8mm through 12.7mm).

Chrome swivel, made of alloy steel reduces friction. Forged yoke made of heat-treated steel. Housed in a blow-molded storage case.

4504
Bubble (I.S.O.) Flaring Tool Kit

Designed for crack-free bubble flares on soft steel tubing used in automotive brake systems.

Includes four dies: 4.75, 6, 8, and 10mm adapters.

Forged steel yoke, flaring bar, and all the adapters needed for ISO bubble flaring.

The most economical “Bubble” flare tool to date. Housed in a blow-molded storage.

4505
Bushing Driver Set

Enables you to remove and install bushings ranging from 3/8" to 1-3/8" in diameter, as used in cars, trucks, tractors, construction equipment, electric motors, and many other components having bushings.

Includes: Large, medium, and small driver handles with nuts; sixteen bushing adapters ranging from 3/8" to 1-3/8".

Housed in a blow-molded storage case.

4506
Fuel Line Clamp Set

Set of two pinchers. Used to quickly shut off flow from vacuum, brake, and fuel lines.

Enables you to pinch and hold hose without damage.

4507
Bearing Race & Seal Driver Set

Permits installation of tapered bearing races and seals without damage to the component or housing. Includes a driver handle plus popular bearing and seal drivers, ranging from 1.565" to 3.180".

Tapered side of driver is used to install races. Invert the driver to the flat side to install seals. Set is housed in a blow-molded plastic storage case.

Includes driver handle with bolt, plus these tool sizes: 1.565", 1.750", 1.965", 2.325", 2.470", 2.555", 2.830", 2.995", and 3.180".

4508
Professional Style Seal Puller

Designed to remove oil and grease seals when servicing cars, SUVs and light trucks without damaging the housing or bearing.

Hook tips in two sizes and professional handle design allows removal of hard-to-get-at seals by getting under them.

The hook tip is double-secured versus competitors, for safety and durability.

An extra blade is included, and additional replacements (No. 4508-1) may be ordered.

4509
Straight-Blade Hose Cutter

Cuts rubber hoses ranging from 1/4" to 1-1/2".

Simply place hose in tool and squeeze handle to cut.

Replacement steel cutter blade No. 4509-1 is available.

4510
Hose Pinch-off Pliers Set

Shuts off flow through vacuum lines, fuel lines, coolant lines, etc.

Cocking ratchet mechanism holds pivoting jaws tightly in place. Heavy-duty swivel jaws pivot to assure parallel pinching.

These three tools are available separately:
4510-8</> – 8" tool for small hoses and tight areas
4510-10</> – 10" tool for radiator and vacuum lines
4510-12</> – 12" tool for radiator and vacuum lines

4511
Hose Cutter - "Guillotine"

Hooks and cuts plastic lines and rubber hoses from 1/8" to 1" diameter. Simply hook hose in V-shaped end, and squeeze handle to cut. Compound mechanical leverage provides power. Spring-loaded blade returns to open position after use, so blade is not exposed.

Linear design with hook feature reaches, grabs, and cuts hoses in tight areas.

Replacement steel cutter blade No. 4511-1 is available.

4512
Snap Ring Pliers Set - Internal/External

For internal or external snap rings; thumbscrew permits quick conversion. Made of heavy-gauge tempered steel. Also includes two stainless steel handled picks.

Contained in a blow-molded plastic storage case.
Contents of Set:
No. 4512-1</> – .090" tip - straight pliers
No. 4512-2</> – .090" tip - 90° pliers
No. 4512-3</> – .070" tip - straight pliers
No. 4512-4</> – .070" tip - 90° pliers
No. 4512-5</> – .047" tip - straight pliers
No. 4512-6</> – .047" tip - 90° pliers
No. 4512-7</> – .038" tip - straight pliers
No. 4512-8</> – .038" tip - 90° pliers
No. 4512-9</> – Straight tip pick
No. 4512-10</> – 90° tip pick

4513
Heavy-Duty Snap Ring Pliers Set

Heat treated steel “circlip” pliers for large equipment repair. Replaceable tips and spring ratchet locking mechanism to securely hold against snap ring tension.

Internal plier’s capacity 3-1/16" to 6-1/4" (78mm to 159mm) snap rings.

External plier’s capacity 3-1/2" to 6-1/2" (89mm to 165mm) snap rings.

Blow-molded storage case includes extra sets of replaceable 0.12" (3mm) dia. tips: straight, 45°, and 90°.

4514
Mini Snap Ring Plier Set

Small-size pliers for work in tight areas. Service S-ring and R-ring clips, internal or external, straight or angled. Ruggedly built of heat-treated chrome molybdenum steel.

Set includes two internal snap ring pliers (one straight, one 45°) and two external snap right pliers (one straight, one 45°).

All pliers have .038" (1.0mm) diameter tips.

4515
Mini Pick & Hook Set - 4 Piece

Sturdy stainless steel points and shafts designed for marking, removing o-rings, accessing snap rings, and performing other tasks. Assorted angle tips allow you to reach awkward locations.

Knurled shaft design enhances finger control for delicate jobs

4518
5-Ton Bar-Type Puller/Bearing Separator Set

This combination set includes our two most popular bearing “splitters” (2" and 3"), four sets of hex push-puller legs and a bar-type puller head with a 9/16" forcing screw. Separator tools are used with bar puller and legs for a wide variety of pulling jobs.

The 5" puller cross-bar with a 6-1/4" forcing screw or each of the bearing separators may also be used separately or in combination with other pullers or tools.

A blow-molded plastic storage case keeps set contents organized and protected from loss.

4520
Differential Side Bearing Puller

Use to remove differential side carrier bearing. Works on a wide variety of cars and light-duty trucks.

Includes four step plate adapters to fit carrier bearings.

Reach: 1-5/8". Spread: 2-5/8" to 3-3/8". Forcing screw is 3/4"-16 mm x 6-11/16" lg.

Set includes:
4520-1</> Forcing Screw / Cross Block Assembly
4520-2</> Puller Jaws / Pins (set of two ea.)
4520-3</> Puller Jaws Retaining Yoke
4520-4</> Step Plate Adapters (set of four)
1-1/8" – 1-1/2" diameter
1-1/8" – 1-5/8" diameter
1-1/2" – 1-5/8" diameter

4528
Clutch Alignment Tool Set

Essential for clutch installation on virtually all cars and light-duty trucks. Aligns clutch plate properly by using tapered cones and pilot adapters.

Includes seven fractional pilot adapters, one clutch disc centering adapter and one alignment shaft.

Includes five metric pilot adapters, two clutch disc centering adapters and one alignment shaft.

Housed in a blow-molded storage case.

4529
Power Steering/Alternator Pulley Puller/Installer Set

Properly replaces pressed-on power steering and alternator pulleys on Ford, Chrysler, and late GM engines.

Housed in a blow-molded plastic storage case.

4530
Power Steering Pump Pulley Service Set

A complete set of tools required to remove and install power steering pump pulleys of most domestic vehicles.

Fits pulley hubs with diameters of 1- 1/8", 1-1/4", 1- 5/16" and 1-3/8".

Includes the necessary adapters for servicing: GM 3.1 L, 3100, 3400, and 3800 V6 engines, GM 2.3L Quad 4 four-cylinder engines and Ford 4.6L, 5.4L, and 5.8L modular V8 engines.

Housed in a blow-molded storage case to protect and organize components.

4531
Harmonic Balancer Puller/Installer Set

For easy removal of most harmonic balancers and drive pulleys which are press-fitted onto the crank-shaft. A bearing-centered circular 2/3-way and an assortment of metric and fractional bolts and adapters provide wide coverage.

A heavy-duty, 3/4" dia. forcing screw is internally threaded to fit the eight adapters to install harmonic balancers. Adapter sizes included: M16 x 2.0, M14 x 1.5, M12 x 1.5, 1/2"-20, 7/16"-20, 3/4"-16, 5/8"-18, and 9/16"-18.

A blow-molded plastic storage case keeps set contents organized and protected from loss.

4533
GM W-Body Strut Tool Kit

Includes one T50 TORX® bit, a universal drive handle, and a double-ended socket.

Use one end of the socket to remove/install the jounce bumper; the other end to remove/install the strut cap nut.

Works on GM W-body vehicles.

Set includes:
4533-1</> Double-ended Socket
4533-2</> Drive Handle
N/A</> T50 TORX® Bit

4534
Multipurpose Bearing & Pulley Puller Set

For a wide range of pulling jobs, including: bearings, alternators, generators, power steering and crankshaft pulleys, timing gears, and harmonic balancers.

Set includes drop-forged components, which can be used in a variety of combinations.
Contents of Set:
2 – Forcing Screws</> (Live Center): 3/4"-16 x 6-11/16" and 3/4"-16 x 5"
2 – Cross-bar Yokes:</> 3 pin-hole @ 3-1/4" to 5-1/2", 2 pin-hole @ 2-3/8" to 3-3/8"
2 – Clamp Bolts</>
3 – Pairs of Puller Jaws:</> 1-3/8" Max, 1-5/8" Max, 1-3/4" Max
1 – Pair of Jaw Pins</> with Ball Spring
3 – Pairs of Capped Bolts</>

Spread: 3" to 5", Reach: 1" to 2-1/4"

Housed in a blow-molded plastic storage case.

4535
A/C Clutch Hub Remover/Installer Set

For damage-free removal and installation of the clutch hubs on these air conditioning compressors: GM-Harrison DA-6, HR-5, V-5, A-6 and early R4; Nippondenso Ford/Chrysler A590, C171, FS-6, 6P148A (new style); Sanden & Sankyo; York/Tecumseh HR980; Zexel/Mitsubishi CH series.

Set includes a removing flange, plus forcing screws and adapter assemblies to remove and install virtually all clutch hubs.

Includes blow-molded plastic case.

4536
A/C Clutch Pulley Puller Set

For removal of stubborn air conditioning clutch pulleys. Also can be used on many alternator, generator, power steering and crankshaft pulleys, harmonic balancers, and fiber timing gears.

Set includes drop-forged components: one 3/4"-16 x 5" live center forcing screw, 5-1/2" crossbar with 3 spread settings, two pair of jaws, and a clamp bolt.

Spread: 3" to 5", Reach: 1" to 5"

Includes blow-molded plastic case.

4537
A/C Clutch Holding Tool

This three-stud spanner wrench keeps the A/C clutch from turning when loosening or tightening the retaining nut. Adjusts quickly with brass thumbscrews to fit various styles of A/C compressors used on GM, Ford, and Chrysler vehicles. Also fits a variety of other pulleys.

4543
Locknut Socket Set

Chrome vanadium steel sockets cover most SUV and light truck applications.

Sockets have 1/2" square drive, allowing use of a torque wrench, ratchet, or breaker bar.

A blow-molded plastic storage case keeps set contents organized and protected from loss.

4547
Axle Nut Socket Set - FWD

Extra long, 1/2" drive 6-point chrome molybdenum sockets for heavy-duty use in removing and installing axle nuts.

Use with a ratchet, breaker bar, or torque wrench.

Contained in a blow-molded plastic storage case.

4550
Scraper Set

Scrapers feature polished, heat-treated, stiff, stainless steel blades. Handles are ergonomic two-component plastic and feature a non-slip grip and steel bolstered end. Packaged in a storage tray. Includes: 1-1/4" straight blade, 1-1/4" bent blade, and 2" straight blade.

4551
Small Door Panel & Upholstery Tool Set
Heavy-duty tools with stainless steel blades used for removing small door panel and upholstery clips: U-notched tool (No. 4551-1); V-notched tool (No. 4551-2).

4552
Putty Knife Set
Heavy-duty stainless steel, precision ground and polished. Blades taper at tip to provide great flexibility and blade action. Ergonomic, two-component plastic handles provide a non-slip grip. Packaged in a storage tray. Includes: 1-1/4" flexible blade knife, 2" flexible blade knife, and 3" flexible blade knife.

4554
Torque Angle Gauge

Required when servicing many late model engines that use torque-to-yield fasteners. Measures angle of rotation after pre-torque in torque-angle applications.

The 360° scale is marked in 2° increments and intervals of 10° and 30°; easily zeroed for next application by turning the tool housing.

Has 1/2" male and female square drives.

4555
Heavy-Duty Oil Filter Wrench

Fits filters ranging from 4-1/8" to 4-21/32" (104 mm to 118 mm) in diameter.

Features a 1-1/2" wide steel band that can stand up to the high torque needed to remove filters from trucks, tractors, and other heavy equipment.
• Use with a 1/2" drive ratchet or breaker bar.

4556
Heavy-Duty Oil Filter Wrench

Fits filters ranging from 4-21/32" to 5-5/32" (118 mm to 131 mm) in diameter.

Features a 1-1/2" wide steel band that can stand up to the high torque needed to remove filters from trucks, tractors, and other heavy equipment.

Use with a 1/2" drive ratchet or breaker bar.

4557
Heavy-Duty Oil Filter Wrench

Fits filters ranging from 5-5/32" to 5-21/32" (131 mm to 144 mm) in diameter.

Features a 1-1/2" wide steel band that can stand up to the high torque needed to remove filters from trucks, tractors, and other heavy equipment.

Use with a 1/2" drive ratchet or breaker bar.

4559
Manual / Pneumatic Pickle Fork Set

Use to separate ball joints, tie rods, and Pitman arms.

Set contains two handles: knurled handle allows use of a hammer; smooth handle fits in a pneumatic hammer.

Three sizes of pickle forks included: 1-1/8", 15/16", and 11/16".

Set contains:
4559-1</> Fork Heads (set of three: 11/16", 15/16", & 1-1/8")
4559-2</> Handles (set of two: knurled handle for use with a hammer; smooth handle for use with an air hammer)

4560
Small Adjustable Oil Filter Pliers

Forged jaws with sure-grip teeth grab the filter for easy removal.

Slip-joint ratchet and lock mechanism allows a secure grip on filters ranging from 2-1/4" to 5" (57 mm to 127 mm) in diameter. Pliers is 13-1/2" long.

4561
Large Adjustable Oil Filter Pliers

Forged jaws with sure-grip teeth grab the filter for easy removal.

Slip-joint ratchet and lock mechanism allows a secure grip on filters ranging from 3-3/4" to 7" (95 mm to 178 mm) in diameter. Pliers is 18" long.

4562
Adjustable Oil Filter Pliers Set
Includes small pliers: 13-1/2" long and fits filters ranging from 2-1/4" to 5" (57 mm to 127 mm) in diameter. Large pliers: 18" long and fit filters ranging from 3-3/4" to 7" (95 mm to 178 mm) in diameter.

4565
Swivel Handle Oil Filter Wrench

Fits filters ranging from 2-7/8" to 3-3/8" (73 mm to 85 mm) in diameter.

Features a 1" wide stainless steel band for positive grip on the filter; swivel handle makes it easy to turn filters in hard-to-reach areas.

4566
Swivel Handle Oil Filter Wrench

Fits filters ranging from 3-3/8" to 3-3/4" (85 mm to 95 mm) in diameter.

Features a 1" wide stainless steel band for positive grip on the filter; swivel handle makes it easy to turn filters in hard-to-reach areas.

4567
Swivel Handle Oil Filter Wrench

Fits filters ranging from 3-3/4" to 4-3/8" (95 mm to 111 mm) in diameter.

Features a 1" wide stainless steel band for positive grip on the filter; swivel handle makes it easy to turn filters in hard-to-reach areas.

4568
Oil Filter Wrench – 3-Leg

Fits filters ranging from 2-1/2" to 5-1/4" (65 mm to 135 mm) in diameter.

To turn the tool, use a 1/2" ratchet in the ratchet drive or a 13/16" wrench on the nut.

Knurled legs provide extra gripping power.

4569
2-Way Oil Filter Wrench – 3-Prong

Use to loosen or tighten oil filters; short-prong design makes the tool easy to use in tight areas.

Fits filters ranging from 2-1/2" to 4-3/4" (65 mm to 120 mm) in diameter.

To turn the tool, use a 1/2" ratchet in the ratchet drive or a 13/16" wrench on the nut.

4573
Universal Overhead Valve Spring Compressor

Permits removal and installation of valve springs with out removing the cylinder head on many cars and light trucks. Durable steel construction.

Spring loaded offset jaws easily grip and compress valve springs.

4576
Universal C-Frame Nut Splitter

Forged and heat-treated frame with offset handle works where ordinary nut splitters may fail. Smooth action cracks nuts without damaging bolt threads.

Chisel rotates to line up parallel to bolt. Splits non-heat-treated nuts of 7/16" (11mm) through 3/4" (19mm) diameter. Tool is 6-3/4" in length.

4577
Strap-Style Oil Filter Wrench

Fits filters up to 6" (152.4 mm) in diameter.

Features a strong, nylon strap that won’t slip off the filter.

Use with a 1/2" drive ratchet or breaker bar.

4581
Blind Hole Bearing Puller Set

For pulling jobs requiring an internal pull, such as pilot bearings.

Set includes four collets which fit a wide range of applications. Select the appropriate sized collet by comparing it with the application. Insert the collet, expand it to fit the hole, then attach the slide hammer assembly.

Four collet sizes: 3/8" to 1/2", 9/16" to 11/16", 5/8" to 1", 1" to 1-1/4".

Set includes a 2- 1/2 pound slide hammer with T-handle.

Housed in a blow-molded plastic storage case.

4585
Ford Fan Clutch Wrench Set

Set contains five of the most popular wrenches used to service water pumps and fan clutches, and other components on the front of Ford engines.

Set contains three holding tools and two turning tools. Use with a 1/2" breaker bar or ratchet.

Replacement parts:
4585-1</> 48 mm (1-7/16") Turning Wrench
4585-2</> 83 mm (3-1/4") Holding Wrench
4585-3</> 72 mm (2-13/16") & 54 mm (2-1/8") Holding Wrench
4585-4</> 40 mm (1-1/2") Turning Wrench
4585-5</> 76 mm (3") & 68 mm (2-11/16") Holding Wrench

4589
Disc Brake Piston Tool

This “cube” tool rotates pistons back into brake calipers when replacing brake pads on vehicles with rear wheel disc brakes.

Tool has 3/8" square drive, provides six drive pin configurations to fit most cars and light trucks. This updated version fits more applications than many competitors.

4590
Brake Spring Pliers & Claw

Effectively removes and replaces shoe return springs of drum brakes on domestic cars and trucks. Thin, narrow point provides straight, in-line pull on spring.

Robust handle provides powerful leverage. Double-ended design. Plated steel resists corrosion.

4591
Brake Spring Compressor Tool

Provides leverage to remove and install stubborn hold-down springs of drum brakes on cars and light trucks.

Special beveled cup end and notched design grips the retaining washers (11/16" to 7/8") used to hold the springs in place. Comfortable handle and knurled base for solid gripping.

4592
Truck Brake Spring Pliers
Designed to remove and install the brake shoe return springs on medium-duty and heavy-duty drum brakes.

4600
Punch & Chisel Set

Durable set of heat-treated chrome vanadium steel punches and chisels. Storage tray included.

Contents of set, available separately:
3 – Cold chisels</> (with gauge): 3/8" x 5-1/2"; 1/2" x 6"; 5/8" x 6-1/2"
2 – Center punches</>: 1/8" x 5"; 3/16" x 6"
5 – Pin punches</>: 3/32" x 4-1/4"; 1/8" x 4-3/4"; 5/32" x 5"; 3/16" x 5-1/4"; 1/4" x 5-3/4"
5 – Taper punches</>: 3/32" x 5-1/4"; 1/8" x 5-3/4"; 5/32" x 6"; 3/16" x 6-1/4"; 1/4" x 6-3/4"

4602
Brass Punch Set

Two large, brass non-sparking punches. Ideal for use near precision parts or in locations where sparks from ferrous metal could be hazardous.

Includes an 8" punch (5/8" hex, tapered to 3/8") and 10" straight punch (3/4" dia., chamfered at both ends.)

4603
Frost Plug Remover/Installer Set

Designed to remove and install frost plugs used in liquid-cooled gas and diesel engines found in automobiles, trucks, SUVs, agricultural equipment, and construction equipment.

Simply use a hammer with the driver and appropriate disc to install frost plugs ranging from 1" to 2-3/8" in diameter.

Set contains: No. 4603-1 Installer Handle (18" lg.); No. 4604-2 Frost Plug Remover; No. 4604-3 Frost Plug Disc Set (7 ea., plus 1 retaining nut).

4604
Frost Plug Installer Set

Designed to install frost plugs in liquid-cooled gas and diesel engines found in automobiles, trucks, SUVs, agricultural equipment, and construction equipment.

Simply use an air hammer with the driver and appropriate disc to install frost plugs ranging from 1" to 2-1/16" in diameter.

Set contains: No. 4604-1 Driver (14" lg.); No. 4604-2 Frost Plug Disc Set (3 qty.).

4605
Interchangeable Punch & Chisel Set

Safety protective handle allows easy grip and protects hand from being hit by hammer.

12 punches and chisels included:
5 flat chisels:</> 1/2", 5/8", 3/4", 7/8", and 1" wide blades
1 cape chisel:</> 1/4" wide blade
2 taper punches:</> 1/8" and 1/4" diameter
2 pin punches:</> 3/16" and 1/4" diameter
2 center punches:</> 1/8" and 3/16" diameter

Double locking ball detent holds punch or chisel securely in the driver handle.

Replacement parts available:
4605-1 Drive handle
4605-2 1/2" wide flat chisel
4605-3 5/8" wide flat chisel
4605-4 3/4" wide flat chisel
4605-5 7/8" wide flat chisel
4605-6 1" wide flat chisel
4605-7 1/4" cape chisel
4605-8 1/8" taper punch
4605-9 1/4" taper punch
4605-10 3/16" pin punch
4605-11 1/4" pin punch
4605-12 1/8" center punch
4605-13 3/16" center punch

4611
Battery Terminal Puller

Designed to remove the battery cable clamp from the post without causing damage to the battery.

Spring-loaded sharp jaws get under the clamp for a secure grip.

4612
3-Way Battery Post Cleaner

Steel blades quickly clean top-post battery terminals and cable clamps; cleaners are marked “positive” and “negative.”

Ream is tapered to clean both postive and negative battery cable clamps.

4613
Battery Pliers

Serrated jaws firmly grip the battery terminal nut or bolt.

Offset handles allow access in hard-to-reach areas.

Works on both top-post and side-post battery terminals.

4614
Side-Terminal Battery Wrench

Designed for use on GM side-terminal batteries, or any 5/16" hex head battery bolt.

5/16", 6 point, box end, 5-1/2" long, ratcheting wrench; insulated handle.

4615
Long Side-Terminal Battery Wrench

Designed for use on GM side-terminal batteries, or any 5/16" hex head battery bolt.

Long handle allows access to hard-to-reach battery terminal bolts.

5/16", 6 point, box end, 10" long, ratcheting wrench; insulated handle.

4616
Battery Terminal Wrench - 10 mm

Designed for use on 10 mm battery terminal bolts found on many import and domestic vehicles.

10 mm, 12 pt., box-end ratcheting wrench; 5-1/2" long with insulated handle.

4617
Side Terminal Battery Brush

Designed to clean corrosion from side post batteries.

One brush used to clean battery terminals; other brush used to clean battery cable ends.

Plastic handle resists battery acid.

4618
Battery Brush

Cleans dirt and corrosion from positive and negative battery posts and cable clamps.

Plastic case resists battery acid and most cleaning solvents.

4619
Professional Battery Hydrometer

Displays a battery’s specific gravity on an easy-to-read float; scale ranges from 1.100 to 1.300.

Thermometer indicates what must be added or subtracted from the float reading to arrive at an accurate specific gravity reading for each battery cell.

Flexible tip offers easy access to the battery cells while the battery is still in the vehicle.

4620
Battery Carrier

Use to lift and install most top post and side terminal batteries.

Designed to transfer lifting force to a secure hold on the battery; teeth on jaws offer a secure grip.

Vinyl strap resists battery acid and will not conduct electricity.

4621
Two-liter Battery Filler
Replenish battery water the easy way! The fill nozzle on this container has an automatic shut-off that prevents overfilling; the handle on the side of the container makes the job a snap. Container holds up to two liters of distilled water.

4622
Battery Cable Cutter

Designed to cut copper battery cable and aluminum electrical cable. IMPORTANT: Do not cut steel cable; damage to blades will occur.

Precision-ground cutting blades provide a clean, square cut.

7" lg. handle gives extra leverage when cutting thick cable.

4623
CV Joint Banding Tool and Cutter

Use to install and tighten the "band-it" or strap style clamps on CV joint boots, or on power steering rack and pinion steering gear boots.

Once installed into the tool, tighten the band by turning the handle on the tool; use a socket or wrench on the handle to torque the band to OE specifications.

When the boot clamp has been tightened to specs, cut the band to the correct length by flipping the lever (at the front of the tool) forward.

516508
Battery Service Tool Kit

This kit includes seven favorite battery tools, housed in a rugged, vinyl-coated fabric pouch.

Kit includes: a heavy-duty battery terminal puller, 4-way battery post cleaner and reamer, angled battery nut pliers, GM 5/16" battery terminal ratchet wrench, extra long 5/16" terminal ratchet wrench, 10 mm battery terminal ratchet wrench, and side terminal battery brush.

6267
GM/Chrysler Harmonic Balancer Puller

Special 3-jaw puller design allows the removing of Chrysler and GM damper pulleys in tight engine compartments without removing the radiator.

Applies to GM, 2000 Generation III 4.8L, 5.3L, 5.7L, 6.0L, and 8.1L V-8s. Also works on Cadillac 4.5, 4.6, and 4.9L V-8s beginning in 1988.

Chrysler engines beginning in 1990 thru 2002 can be serviced including 2.0, 2.4 L-4s. Plus 2.5L, 2.7L, 3.3L, 3.5L, and 3.8L V-6s.

Kit contains the 3-jaw puller, three lengths of forcing rods, and a forcing screw with a 3/8" square drive for ratchet use.

6284
Chrysler Harmonic Balancer Puller Set

Allows the technician to remove and install the harmonic balancer on the most popular Chrysler engines.

Includes OTC No. 6267 puller, which removes the harmonic balancer from the crankshaft; and OTC No. 6495 holding tool, which holds the harmonic balancer when tightening or loosening the crankshaft bolt, or
removing the balancer.

6285
LeakTamer

Diagnostic Leak Detection

Speaks to the need of highly popular “smoke” diagnostics at an affordable price.

Make use of a new pressure discharge port to test the flow of smoke and verify solenoid position.

Checking an engine system such as EGR with “smoke” is a visual activity for the technician. He fills the intake manifold with smoke and looks for where it is leaking.

6292
Distributor Bushing Remover

Used to remove the distributor drive shaft lower bushing from the engine block.

Works on Chrysler, Dodge, and Plymouth 3.9 V-6, 5.2 and 5.9 V-8 vehicles with distributors.

6293
Distributor Bushing Installer/Reamer

Used to install the distributor drive shaft lower bushing into the engine block. Then use this same tool to ream the new bushing so the distributor drive shaft fits properly into the bushing.

Works on Chrysler, Dodge, and Plymouth 3.9 V-6, 5.2 & 5.9 V-8 vehicles with distributors.

Compatible with OEM and aftermarket distributor drive bushings

6295
Front End Service Set

This kit includes five popular tools used for servicing Pitman arms, ball joints, and tie rods on most vehicles.

Two Pitman Arm Pullers for large or small ball joint applications.

Two Ball Joint Separators.

Three different T